Fusionskin® Ceramic 3+ 50ml

50ml are sized for 1 car.
The Ceramic 3+ forms an ultra-thin anti-stick layer. This is extremely dirt-repellent, resilient and hard. It deepens it the gloss and color intensity of the paint surface extremely.
Mere hand washing alone will cause wear and tear such as fading and micro scratches. When your vehicle is sealed with our Ceramic 3+, these are reduced to a minimum and the paint surface is sustainably protected.
Self-leveling, permanent barrier layer
Binds chemically to the treated substrate
Excellent corrosion protection Easy-to-clean properties (ETC coating)
Applies and bonds to the substrate at the molecular level
The permanent coating creates a glass-like barrier layer only a few µm thick High chemical and mechanical resistance with high surface tension (hydrophobic properties)
Temperature resistance up to approx. 1000°C.
Self-leveling or microplanarization provides no adhesion surface for dirt particles Permanent gloss and color intensifying effect
Durability at least 3 to 5 years CERTIFIED ACCORDING TO: DIN EN ISO 9227, DIN EN ISO 6270-2, DIN EN ISO 16474-2, DIN 50021Preparation:
1. ambient temperature should ideally be between 20 and 30 degrees.
2. prepare the surface free of scratches perfectly and degrease with Fusionskin Final Check.
The preparation process can be analogous to conventional / known coating substrates.
Application:
Important: NO multi-layer process possible.
The substrate, whether "Ceramic 3+" or "Ceramic 5+" is applied sparingly and carefully with the Fusionskin Ceramic Sponge microfiber applicator to the surface to be sealed in a so-called cross motion.
The corresponding surfaces are first coated horizontally and then vertically.
The amount of substrate can be varied in the application - however, there must be no dripping at the edges.Finishing / rubbing off:
Ceramic 3+: service life 3-5 years / Ceramic 5+: service life 5-10 years
After approx. 2 - 4 minutes (at 20 degrees approx. 4 minutes, at 30 degrees approx. 2 minutes), gently rub the freshly sealed area with a microfiber cloth until a homogeneous surface is created (rub the sealant into the surface, so to speak).
Then wipe with a 2nd clean microfiber cloth. Do not mix up the cloths in the repeat process (it is best to use different colored cloths).
Curing:
The vehicle should not be exposed to the environment for at least 12 hours after sealing. Protect sealant from machanic influences for at least 7 days.
Safety Instructions:
Hazard statements H225 Highly flammable liquid and vapor. H302 Harmful if swallowed. H314 Causes severe skin burns and eye damage. H317 May cause allergic skin reactions. H336 May cause drowsiness and dizziness. H412 Harmful to aquatic life with long lasting effects. Precautionary statements P101 If medical advice is needed, have container or label at hand. P102 Keep out of the reach of children. P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Do not smoke. P260 Do not breathe dust/fume/gas/mist/vapor/aerosol. P264 Wash hands and face thoroughly after use. P271 Use only outdoors or in well-ventilated areas. P280 Wear protective gloves/protective clothing/eye protection/face protection. P301+P330+P331 IF INTOXICATED: Rinse out mouth. DO NOT induce vomiting. P303+P361+P353 IF ON SKIN (or hair): Remove all contaminated clothing immediately. Wash skin with water or shower. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove any contact lenses if possible. Continue to rinse. P310 Immediately call a POISON CENTER/physician. P403+P235 Keep in a well-ventilated place. Keep cool. P405 Keep locked up. P501 Contents / container of an added